MiniH100

Tube Heater & Incubator Selection Guide

Choose by application

Your application Type to choose Models to compare
Routine constant-temperature tube heating Heating-only dry bath MiniH100 · HB105-S1 / S2 · HB120-S / SC · H100-Pro
Below-ambient tube holding with heating Heating/cooling dry bath MiniHC100 · MiniHCL100 · HC110-Pro
Temperature-controlled tube mixing Thermomixer HM100-Pro · HCM100-Pro
Plates, bottles and flasks Chamber incubator EDVOTEK Incubation Oven 546

Choose the heating format first. Dry baths transfer heat through a fitted tube block; chamber incubators heat the surrounding air. Thermomixers add controlled agitation. Check whether the model heats only or also actively cools.

Compare models by category

Temperature setting ranges and achievable operating temperatures differ. “Ambient +5°C” means 5°C above room temperature. Below-ambient cooling depends on room temperature, block and load. Tube capacity depends on the fitted block; confirm the block supplied with your configuration.

Heating-only tube blocks

MiniH100

Compact tube heating

MiniH100

Heating-only work where a small footprint matters.

Temperature
Ambient +5°C to 100°C
Capacity / format
One selected block; tube capacity depends on format.

Selection notes

Compact body, timer and stored programs. Fixed PCR and microplate-block versions are separate options.

View product
HB105-S1 / S2

Routine tube heating

HB105-S1 / S2

General constant-temperature preparation in matched tube blocks.

Temperature
Ambient +5°C to 105°C
Capacity / format
S1: one block; S2: two blocks.

Selection notes

Choose S2 for extra block capacity. Block sizes and included configuration must match your tubes.

View product
HB120-S / SC

Higher-temperature tube heating

HB120-S / SC

Heating tasks requiring a maximum above the 100–105°C range.

Temperature
Ambient +5°C to 120°C
Capacity / format
One interchangeable block.

Selection notes

SC adds single-point calibration. Both are heating-only; optional blocks determine tube capacity.

View product
H100-Pro

Programmable heating

H100-Pro

Temperature-controlled tube or plate work without shaking.

Temperature
Heating to 100°C; lower limit depends on ambient
Capacity / format
Interchangeable tube / plate block.

Selection notes

This is the heating-only model. Select HM100-Pro when active mixing is required.

View product

Heating and cooling blocks

MiniHC100

Compact heating and cooling

MiniHC100

Small-batch work needing both warming and below-ambient control.

Temperature
Listed 0–100°C; cooling limited by ambient
Capacity / format
One selected interchangeable block.

Selection notes

Cooling capability is approximately 23°C below ambient. Confirm the achievable minimum in your room.

View product
MiniHCL100

Heating/cooling with a heated lid

MiniHCL100

Small-volume tube work where cap condensation matters.

Temperature
Listed 0–100°C; cooling limited by ambient
Capacity / format
One selected interchangeable block.

Selection notes

Adds a heated lid to the compact heating/cooling format. Confirm tube height and lid compatibility.

View product
HC110-Pro

Wider-range heating and cooling

HC110-Pro

Block-based temperature control without mechanical mixing.

Temperature
Set range −5 to 110°C; up to 25°C below ambient
Capacity / format
Interchangeable tube / plate block.

Selection notes

No shaking function. Choose the appropriate touch or push-button configuration.

View product

Thermomixers

HM100-Pro

Heating with mixing

HM100-Pro

Tube preparation needing temperature control and agitation together.

Temperature
Heating to 100°C; lower limit depends on ambient
Capacity / format
Selected block; 200–1,500 RPM mixing.

Selection notes

3 mm mixing orbit and stored programs. This model heats and mixes; it does not actively cool.

View product
HCM100-Pro

Heating, cooling and mixing

HCM100-Pro

Flexible tube work requiring all three functions.

Temperature
Set range 0–100°C; up to 15°C below ambient
Capacity / format
Selected block; 200–1,500 RPM mixing.

Selection notes

3 mm mixing orbit. Confirm compatible block, tube format and cooling performance at room temperature.

View product

Chamber incubators

EDVOTEK Incubation Oven 546

Chamber incubation

EDVOTEK Incubation Oven 546

Holding compatible plates, bottles and flasks in a heated chamber.

Temperature
Ambient +5°C to 60°C
Capacity / format
20 L chamber; two adjustable shelves.

Selection notes

Accepts vessels up to 2 L where they fit. An air incubator provides chamber heating rather than direct block contact.

View product

Four checks before you order

1. Match the sample format.
Check tube volume, bottom shape, plate footprint and block well count. Multiple blocks do not automatically mean independent temperatures.

2. Choose heating, cooling or mixing.
Heating-only units cannot hold a setpoint below room temperature. Choose a thermomixer if active agitation is required.

3. Compare temperature performance.
Check accuracy, uniformity and stability under the conditions that matter for your work. Display resolution alone does not describe performance.

4. Check blocks and accessories.
Confirm the number of blocks, tube fit, lids, probes and included accessories. Choose a chamber size that fits your plates, bottles or flasks.

Need help choosing a configuration?

Tell us your tube or plate format, batch size, temperature range and whether you need cooling or mixing.

Request a quote

Specifications: linked Kormay product configurations, DLAB thermal-control catalogue and EDVOTEK 546 specification. Confirm the latest model revision and included accessories.

Newsletter

Join our mailing list for the latest news and special offers.